minimalistic OSD configuration for BetaFlight 3.2 November 03 2017, 0 Comments

The latest generation of Whoop FCs has an OSD chip on board, e.g the BetaFPV F3.
BF 3.2 OSD has a huge list of features, but only a few are useful on micro FC with limited sensor support.

After trying a range of OSD configurations, I settled on
- voltage
- flight time
- warnings
- crosshair
- "battery not full" alert: 4.1V
- "low battery" alert: 3.1V
- "battery critical" alert: 2.9V
- "flight time" alert: 2:00min
- "Clarity" font

Here is how this configuration looks/works:

To configure your OSD as above, you can copy the settings below and paste them into the CLI of your BetaFlight configurator, then enter "save" and enter. If you want to use the same font as above, go to "Font Mamager" and upload the "clarity" font.
Note: these settings are for BetaFlight 3.2. Using them on a different firmware version might not work.

set osd_units = METRIC
set osd_rssi_alarm = 20
set osd_cap_alarm = 2200
set osd_alt_alarm = 100
set osd_ah_max_pit = 20
set osd_ah_max_rol = 40
set osd_tim1 = 2560
set osd_tim2 = 513
set osd_vbat_pos = 2087
set osd_rssi_pos = 40
set osd_tim_1_pos = 54
set osd_tim_2_pos = 2096
set osd_flymode_pos = 333
set osd_throttle_pos = 225
set osd_vtx_channel_pos = 377
set osd_crosshairs = 2248
set osd_ah_sbar = 200
set osd_ah_pos = 200
set osd_current_pos = 385
set osd_mah_drawn_pos = 353
set osd_craft_name_pos = 33
set osd_gps_speed_pos = 218
set osd_gps_lon_pos = 82
set osd_gps_lat_pos = 65
set osd_gps_sats_pos = 51
set osd_home_dir_pos = 302
set osd_home_dist_pos = 303
set osd_compass_bar_pos = 42
set osd_altitude_pos = 247
set osd_pid_roll_pos = 423
set osd_pid_pitch_pos = 455
set osd_pid_yaw_pos = 487
set osd_debug_pos = 1
set osd_power_pos = 321
set osd_pidrate_profile_pos = 345
set osd_warnings_pos = 2186
set osd_avg_cell_voltage_pos = 76
set osd_pit_ang_pos = 33
set osd_rol_ang_pos = 65
set osd_battery_usage_pos = 392
set osd_disarmed_pos = 2315
set osd_nheading_pos = 311
set osd_nvario_pos = 279
set osd_esc_tmp_pos = 82
set osd_esc_rpm_pos = 83
set osd_stat_max_spd = OFF
set osd_stat_max_dist = OFF
set osd_stat_min_batt = ON
set osd_stat_min_rssi = OFF
set osd_stat_max_curr = OFF
set osd_stat_used_mah = OFF
set osd_stat_max_alt = OFF
set osd_stat_bbox = OFF
set osd_stat_endbatt = ON
set osd_stat_bb_no = OFF
set osd_stat_tim_1 = ON
set osd_stat_tim_2 = ON

set bat_capacity = 200
set vbat_max_cell_voltage = 44
set vbat_full_cell_voltage = 41
set vbat_min_cell_voltage = 29
set vbat_warning_cell_voltage = 31
set vbat_hysteresis = 1
set current_meter = ADC
set battery_meter = ADC
set vbat_detect_cell_voltage = 30
set use_vbat_alerts = ON
set use_cbat_alerts = OFF
set cbat_alert_percent = 10
set vbat_cutoff_percent = 100
set vbat_scale = 110